Home > Dvd Drive > Replacing DVD Drives - IDE To SATA

Replacing DVD Drives - IDE To SATA

Contents

When it came out the IDE standards were retroactively renamed PATA or Parallel ATA to distinguish them from SATA or Serial ATA. Find Solutions, ask questions, and share advice with other HP product owners. All Rights Reserved. If you do not know which pins represent Cable Select, check the labeling on the drive, looking for CS.

Figure : Cable Select setting Connect the end of the IDE ribbon cable into the IDE interface connector on the back of the drive as follows: If there is only one Drive enclosure for permanent use. The example I/O controller card below gives you one SATA socket, one PATA socket, and one eSATA (external SATA) socket. Powered by Mediawiki.

How To Connect Ide Dvd Drive To Sata Motherboard

SATA advantages over the older PATA specs include faster data transfer, higher efficiency, hot plugging, reduced cable width, and better internal air flow. The data cable looks like this: The pwer cable looks like this: In general, though not always, a SATA data cable only has one connector, so for each SATA device you Tips Place your computer on its side for easier access. Set the jumpers so that the hard drive is the first or primary drive on the ribbon and the DVD/CD is the secondary or slave drive.

When you reboot your machine the BIOS should automatically detect the new drive. Oturum aç Paylaş Daha fazla Bildir Videoyu bildirmeniz mi gerekiyor? This product gives you a wide black plastic connector you plug onto the rear of your hard drive. Dvd Drive Power Cable See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading...

Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading... Motherboard card slot. Click the plus sign (+) next to DVD/CD-ROM drives. http://www.wikihow.com/Replace-an-IDE-Dvd-Drive-With-an-SATA-Dvd-Drive LEARNINGCHORDS 15.049 görüntüleme 21:29 Install a CD drive - Süre: 3:28.

MESSAGES LOG IN Log in Facebook Google Email No account yet? Optical Drive Power Cable How can I best mix IDE and SATA drives in one system? If you're adding a second IDE drive, set its jumper to Slave.If you're installing a SATA drive, jump to the following step. 5Attach rails to your DVD drive, if your case Most new drives are already set to Cable Select.

How To Connect Dvd Drive To Motherboard

I'm using the Syba product right now on a two-year-old HP Pavilion that has only SATA sockets on the motherboard. Learn More I've focused on readability so I've left out some technical details. How To Connect Ide Dvd Drive To Sata Motherboard More resources Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About How To Install Dvd Drive On Pc how do I boot it from hard drive?

furulevi 73.846 görüntüleme 1:53 Modifying a PATA to SATA Power Cable - Süre: 4:45. Two hard drives are connected: a 1 TB SATA disk and a legacy 160 Gig IDE drive connected with Syba. Install an IDE drive The first step after removing the case covers is to remove the "blank" plastic front from the position in which you want to install the CD/DVD writer You set the jumpers to indicate whether one or two drives on are the same IDE cable, and which drive is where in the sequence. (Connecting SATA disk drives is simpler How To Install Cd Drive In Laptop

In fig 1.3 to the right you can see a standard IDE cable. Anti-static wrist-strap (if available). note: Disconnect the power and remove your PC's cover, see our guide. Remove an old IDE drive After removing the covers the next step is to locate and remove the data and power cables attached to the old device.

The back of the drive looks similar to this one: The data cable that fits into this drive looks something like this: The other end of this cable connects to the Ide To Sata Converter For Dvd Drive Unplug the power cable. It's white and it has a female connector that goes into the 4-pin male connector on the back of the disk drive.

EDIT Edit this Article Home » Categories » Computers and Electronics » Hardware ArticleEditDiscuss Edit ArticleHow to Replace an IDE Dvd Drive With an SATA Dvd Drive Community Q&A In the

Unfortunately some are flimsy or have poor quality control. Transition Drive Uses Either Power Plug  (Gateway) Inspect your motherboard, too. Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is Sata Optical Drive This chart summarizes the three drive integration solutions I've described: USB Toolset: Drive Dongle: Controller Card: Mounts Drive(s): External Internal Internal & External * Requires Software Driver: No No Yes Supports

How can I connect a SATA drive to an old motherboard having only IDE sockets? Figure : Matching the side panel tabs Insert the side panel and slide it forward. It is perfectly acceptable to plug both a hard drive and a DVD drive on the same cable. Some computers use IDE cables with only two connectors, one for the motherboard connection and one for the drive.

Reproductions must be properly credited. Do the same thing on the other side, and remove the bay insert. Switching to a SATA drive will reduce the bulk of cables in your computer, and SATA offers increased speeds for data transfer. The power supply has a 20-pin main connector. 2 answers Last reply Jul 13, 2012 More about replacing optical drive sata optical drive SR-71 BlackbirdJul 13, 2012, 7:07 AM http://www.newegg.com/Product/Product.aspx?Item=N82E16812232004 SR-71

Read his other articles here (0) 15 Comment(s) Related Articles Quantum computing is real, and D-Wave just open-sourced itMaking an MSX fontThe FireBee: modern Atari clone Technology White Papers See Finishing the IDE installation Double check all connections and make sure the device is set correctly as master or slave. Software driver. * Controller cards usually have a eSATA or USB port that allows external mounting. If the drive attaches to the computer with a plastic latch, snap and lock it into place.

The IDE standards applied across thousands of different drive and motherboard manufacturers. Or a cable just connected to a hard drive, but with a spare connector currently unused on the cable, shows an IDE DVD drive will go in your case. IDE cable (if required). All trademarks, icons, and logos shown or mentioned in this web site are the property of their respective owners.

Thanks for letting us know. To the left is an example of a typical IDE cable along with a molex power connector. newmodeUS 40.164 görüntüleme 2:43 Daha fazla öneri yükleniyor... The document also provides instructions for replacing an IDE drive with a Serial ATA (SATA) drive.

Just use the power plug you have, no worries. Label "A" is the SATA power connector, "C" is the "legacy" or IDE power connector, and "B" is the SATA data or "signal" plug. If you are replacing an IDE drive with a Serial ATA (SATA) drive, you may need a PCI SATA controller card or a SATA to IDE adapter.