Home > How To > Did I Just Fry My Motherboard?

Did I Just Fry My Motherboard?

Contents

no fans, no nothing... But even so, yes, you do need to be careful. I don't know how it got loose but it did. I even thought maybe the case jumper was being buggy so used the power jumper from another case, but that didn't work either.... his comment is here

It may not work at all, or it may power on if half the load has gone. Please note - this post may not present all information available on a subject. Silence or long single beeps indicate a problem with the memory.Insert the video card and connect any necessary PCIe power connectors. But the computer turns on and the fans run and everything which leads me to believe it is not the motherboard.

How To Tell If You Fried Your Motherboard

I took out the GPU, and switched out the PSU as I already had a working PSU and it still didn't turn on. solved Did I fry my motherboard? what do you guys think?

permalinkembedsaveparentgive gold[–]Sesleri 0 points1 point2 points 3 years ago(0 children)I shut off the power strip with my foot by accident on my $1000 rig all the time :D it's nbd When I built When trying to start the only sign of life i see is that the fans start, but i get no VGA-bios screen or any beep. I don't have a voltage tester - is there any other way I can conform it's the PSU? solved Wrong ram installed did i fry my motherboard Did this computer just fry itself?

I suspect that my 12v source might have touched some of the leads that go to the parallell port. Fried Motherboard Symptoms Mar 10, 2004 Posts: 334 View posts Location: UK #11 Posted by prime: Tue. Good luck to you though. Fuses in power supply units may be replaceable by the end user, but fuses in consumer equipment may require tools to access and change.

Long story short, was running, touched mobo, system rebooted, and now everything's running but it wont detect any peripherals. Also, i added a line that moved the hex-file to the share were the programmer computer could access it. Did I just fry my VRM? solved How did my motherboard fry?

Fried Motherboard Symptoms

If it was fast, I would guess your caps might have survived. https://arstechnica.com/civis/viewtopic.php?f=8&t=563858 Whatever the reason, I have just placed a bid on a new system. How To Tell If You Fried Your Motherboard Tolerances are +/- 5% except for the -12 volts which is +/- 10%.The gray wire is really important. Is My Motherboard Dead But even if it might look about the same....do NOT confuse this with the 4pin 12V CPU connector !

I hasseled around a bit to see if all was plugged in right, (thats when I discovered the 4pin) plugged that in then nothing happened. You do have a case speaker installed, right? permalinkembedsaveparentgive goldaboutblogaboutsource codeadvertisejobshelpsite rulesFAQwikireddiquettetransparencycontact usapps & toolsReddit for iPhoneReddit for Androidmobile websitebuttons<3reddit goldredditgiftsUse of this site constitutes acceptance of our User Agreement and Privacy Policy (updated). © 2017 reddit inc. solved Did I fry my motherboard? How To Reset Cmos

CPU, the other rail is separate and provides power for the pci-express card.) This is not necessarely bad In other words: You cant go wrong with a new 24pin PSU for I get no signal on my monitor. Media Center: Motherboard: Gigabyte mp61p-S3, Processor: AMD Athlon 64 x2 6000+, Memory: 6 gigs Patriot DDR2 800, Video: Gigabyte GeForce GT730, Storage: 500 gig Hitachi, PSU: Seasonic M1211 620W full modular, Do the paper clip test on your PSU and then go through the troubleshooting steps below to make sure you haven't missed something.http://www.tomshardware.com/forum/261145-31-perform-steps-posting-post-boot-video-problems Reply to BadActor BadActorSep 30, 2016, 2:01 AM

A 20pin -> 24pin PSU adapter would not "magically" provide more power/amperes and not solve your problem. If you dont have this adapter - newegg has one pci-express power adapter (!) a single connector/wire on a PSU/connector is usually rated at a max. solved did I fry my cpu or what?

I would have a sense of achievement when it was done.

Jun 9, 2004 Posts: 8 View posts #5 Posted by simon78: Thu. Started by DerBear89 , Oct 28 2010 08:48 PM Page 1 of 2 1 2 Next Please log in to reply 17 replies to this topic #1 DerBear89 DerBear89 Members 62 You may see some fuses inside. Nforce 4) SHOULD be capable of running with an "old" ATX 1.3 20pin-plug equipped PSU as well as with a new ATX 2.0 24pin PSU.

Using the on-board video VGA port to run a monitor?I have also read that the newer Intel boards require the extra 4 pin connector to work properly, and perhaps could cause The most strain wil be on the adapter/plugs itself. After that I plugged in just the bare essentials and tried to boot. I did have to do one or two tricks to make it work; 1) fix autologon to the programmer computer, there's a guide at OpenSSH site. 2) setup a share that

Can't find your answer ? I find it hard to believe (though not entirely out of the question) that you not having it plugged in fried the board.Just a few days ago, I rebuilt my HTPC more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science Could it be the CPU or the RAM?

If your PSU appears to be dead. If my motherboard is fried does it mean it took my CPU out with it? Again, the warranty info should have been included in the paperwork for the product. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...